Product name search
Continuous Soffit Vent with large 1/4" (6 mm) hole configuration that offers excellent air flow and at the same time resists paint clogging. Excellent bond to stucco, also rustproof. Product #549-75-25 has a 1" (25 mm) nailing flange for easier installation.
Arlington Industries’ IN BOX® for new siding is now available from Plastic Components! This one-piece, recessed electrical boxes save labor time, and because IN BOX® installs in the wall, you’ll get a great-looking job too. The cover protrudes from the wall just enough for a neat, clean appearance. And IN BOX, for new siding, has flanges that cover the cut ends of siding.
• No gaskets required
• For all siding types
• Clear or paintable white cover
• UL/CSA Listed weatherproof while-in-use
• Meets NEC 2020 (National Electric Code) and CEC (Canadian Electric Code) 2015
Offers aesthetic value as a low profile, non-metallic electrical box that installs IN the wall. It accepts most single-gang wiring devices and uses standard indoor wall plates of a GFCI cover plate.
ULTRA-LATH PLUS® is designed for exterior or interior vertical or horizontal application. It’s 1/4" self-furring ridges provide exceptional keying and should be applied with the ridges toward the substrate. ULTRA-LATH PLUS® meets ASTM C1764, C1788, C1780, C1063, C1861 and C1787 and is impervious to sand and any harsh chemicals found in portland based stucco. IT WILL NEVER RUST. It may be installed over any code approved substrate. ULTRA-LATH PLUS® now complies with 2020 FL Building Code and Metro Dade County HVHZ requirements for Impact and Cyclic performance (TAS 201, 202, 203) and is recognized by IAPMO Uniform Evaluation Services report #0284 as code compliant to the 2009 and 2012 International Building Code and Institute for Research for Construction (Canada).
A surface mounted vent suitable for all applications except three coat stucco systems. Vent installs easily on all sheathing products depending on the substrate with either spray adhesives, staples and/or screws according to substrate manufacturers' technical details. Vent holes 1/8" (3 mm) diameter. All flanges must be base coated and covered with mesh per system manufacturer.
A surface mounted vent suitable for all applications except three coat stucco systems. Vent installs easily on all sheathing products depending on the substrate with either spray adhesives, staples and/or screws according to substrate manufacturers' technical details. Vent holes 1/8" (3 mm) diameter. All flanges must be base coated and covered with mesh per system manufacturer.
Designed for use with sheathing products. For use when a horizontal soffit and a vertical plan intersect. Vent holes 1/8" (3 mm) diameter. Attach the F-clip to either the vertical fascia board or intersecting vertical wall with the wide flange of the F-clip extending downward, then insert the perforated vent into the F-clip.
Designed specifically for sheathing products. Has a built-in stop (1/8"-3 mm) to assure proper base thickness as well as maintaining a clean finish edge. The stop flange is serrated for positive material bond. Vent holes 1/8" (3 mm). Will not rust, excellent paint adhesion. Connector clips are provided to eliminate sagging at butt joints.
Designed specifically for sheathing products. Has a built-in stop (1/8"-3 mm) to assure proper base thickness as well as maintaining a clean finish edge. The stop flange is serrated for positive material bond. Vent holes 1/8" (3 mm). Will not rust, excellent paint adhesion. Connector clips are provided to eliminate sagging at butt joints.
A vent screen trac for use with EIFS systems. The VST has a double row of drainage holes that aid in carrying moisture away from the structure. Its 2" (51 mm) wide nailing flange, and the nail holes set every 4" (102 mm) o.c. provide secure attachment. It also provides superior bond of base coat to foam board.